- Nedavno
![AC 110-220V termometar Hygrometer temp kontroler vlage Hygrostat Thermostat SHT20 sonda za akvarij inkubator hladnjak AC 110-220V termometar Hygrometer temp kontroler vlage Hygrostat Thermostat SHT20 sonda za akvarij inkubator hladnjak](/route/iskra/gonzo-4/26426-ac-110-220v-termometar-hygrometer-temp-kontroler-vlage-hygrostat-thermostat-sht20-sonda-za-akvarij-inkubator-hladnjak.jpg)
AC 110-220V termometar Hygrometer temp kontroler vlage Hygrostat Thermostat SHT20 sonda za akvarij inkubator hladnjak
AC 110-220
V termometar higrometar temp kontroler vlage Hygrostat Thermostat SHT20 sonda za hladnjak akvarij inkubatora. AC 110-220
V Termometar Higrometski kontroler vlage Hygrostat Thermostat SHT20 SPECIFIKAT : Ime proizvoda : Temperatura i vlažnosti
Proizvod : AC 110 -230
VPower Opskrbnost : 50 / 60
Hzsensor Dužina sonde : 1
Sensors Sonda Tip : SHT20temperature Opseg mjerenja : -20 -60 ℃ Raspon mjerenja vlage : 0% -100% Prečlana mjerenja Rhtempereture : 0.3 ℃ Vrijednost vlage : 3% Izlazna kontrola : relej outpueutput snaga : max 10asize : 93 * 56 * 34mmpsetting : metoda podešavanja : Postavljanje vrijednosti : Pokretanje vrijednosti Zaustavka (program automatski određuje način rada za hlađenje / odvlaživanje) Način grijanja / hlađenja Metoda : Podešavanje (startna temperatura) : Dugm Pritisnite tipku ▲, a startna temperatura treperi, a vrijednost startne temperature postavljaju ▲ ▼ Tipke (Stop Temperatura) : Dug Pritisnite tipku ▼ da biste zaustavili temperaturu, postavite temperaturnu vrijednost ▲ ▼ u slučaju tipkala : Upravljajte bojler, grijanje na 65 ℃ za zaustavljanje, temperatura pada na 50 ℃ na Pokrenite prvog koraka : režim rada grijanja, startne temperature TEMPETEPEP 2 : Pritisnite i držite tipku za početnu temperaturu, a zatim postavite početnu temperaturu na 30 ℃ putem tipke ▲ ▼ na tipku ▲ ▼ na Zaustavite temperaturu treperi i podesite temperaturu zaustavljanja na 26 ° C sa tipkom ▲ ▼. Podešavanje je kompletno! Podešavanja vlažnosti / odvlaživanja / dehumidifikacije : Podešavanje (startna vlaga) : Duga pritisnite tipku △, pletene vlažne vrijednosti, a postavite vrijednost start vlage pomoću tipke △ ▽. Podesite [STOP vlažnost] : Duga pritisnite tipku △, zaustavite vrijednost vlage treperi i postavite zaustavljanje vlage pomoću tipke tipke △ ▽ .exa.
Više detalja
- Product Name:
- Temperature and Humidity Controller
- Product model:
- DTC3200
- Power supply voltage:
- AC 110 -230V
- Power supply frequency:
- 50 / 60Hz
- Sensor Probe Length:
- 1m
- Sensor Probe Type:
- SHT20
- Temperature measurement range:
- -20 -60 ℃
- Humidity measurement range:
- 0% -100% RH
- Temperature measurement accuracy:
- 0.3 ℃
- Humidity measurement accuracy:
- 3%
- Output control:
- Relay output
- Output power:
- MAX 10A
- Size:
- 93*56*34mm
- Setting:
- Setting method:
- start value stop value (the program automatically determines the working mode to be cooling / dehumidifying mode)
- Heating / cooling mode setting:
- Setting method:
- setting (starting temperature)
- Setting (stop temperature):
- long press the ▼ button to stop the temperature flashing, set the stop temperature value by ▲ ▼ button
- Heating use case:
- control the water heater, heating to 65 ℃ to stop, the temperature drops to 50 ℃ to start heating again
- The first step:
- heating working mode, start temperature stop temperature
- Step 2:
- Press and hold the ▲ button, the starting temperature flashes, and set the starting temperature to 30 ℃ via the ▲ ▼ button
- Step 3:
- Press and hold the ▼ button to stop the temperature flashing, and set the stop temperature to 26 ° C with the ▲ ▼ button. The setting is complete!
- Humidification / dehumidification mode settings:
- Setting (Start Humidity):
- Long press the △ key, the start humidity value flashes, and set the start humidity value with the △ ▽ key. Set [Stop Humidity]
- Exa :